-
Text Box Issues
I am having ongoing problems with my textbox tools. Typing is distorted, especially using the space key (which doesn't do anything) or any punctuation marks. After using punctuation marks, cursor position changes and/or text starts in putting back to front. Upon trying to re-edit a already used textbox, I am unable to…
-
Bluebeam Session Limitations
I'm looking to understand certain limitations and request that Bluebeam allows for users to opt out of the restrictions currently put on sessions to offer a more collaborative environment within sesesions. I have (3) issues currently with Bluebeam that seem unnecessarily restrictive. Ability to Replace Pages within a…
-
Hyperlink enbedded in stamp
I am trying to add a stamp to a document in plan review that has a link to local ordinances. Is there a way to keep that link active after the review has been closed so that the contractor or inspector can click on the link ?
-
custom columns on markups
I have created a lot of custom toolchests, and have added some custom columns. I have used them on several documents and exported the summaries just fine. Periodically, or when a new team member uses the profile we have shared containing those markups, the custom columns disappear. I need some help.
-
Disconnected length measurement
Does anyone know if this is possible, as in Trimble Live Count. What I call a disconnected length measurement is when I want to measure all the 3/4" conduit in a room, I need to be able to go from one row to the next without the length being added to the total
-
Multiple Legends Within One Document
Re: takeoffs from architectural drawings I cannot figure out how to create multiple legends within one document. I would like to have not only the totals for the entire document, but I would also like to have a count per page legend. I have tried creating a new legend with a new Subject and specific source pages, but it…
-
Allow Markup Recovery (Unflatten) : Always Checked Option
We all flatten and unflatten often with [Allow Markup Recovery (Unflatten) checked for various purposes as we are working through a document. Then, when we are finally ready to distribute a document, we will flatten without markup recovery. I have taught myself to instantly go right back in and flatten again just to check…
-
Anyone else having an issue with visible layers resetting?
I have an ongoing issue where my visible layers reset after using the undo tool and I'm wondering if anyone else is experiencing this? Basically, I have various layers turned off when I am marking up but, after placing a markup incorrectly and then using undo all of the layers are turned on. So I then have to go into the…
-
Segement Values
I may have missed it but I would like to be able to easily see the segment values, even have control over their formats, as these are virtually invisible if you use a low fill value. I dont want to have to use high fill values just to be able to read the segments so tend to not use them, however they would be useful in…
-
Set hyperlink window size?
I create a lot of my own hyperlinks. When I create one the hyperlink window is much larger than the markup? I have to go in an manually adjust the hyperlink window each time to prevent overlap. A lot of my hyperlinks are stacked. Is there a way to set hyperlink window size in preferences? Or, save a hyperlink to tools with…
-
Polyline Behavior Change?
I use a lot of polyline drawing, and rely heavily on making straight lines (holding down the Shift key while drawing). The tool recently started behaving differently, where holding the Shift key does NOT start the line off straight. I have to now lift the Shift key and re-press it to get the line to straighten out. Why is…
-
Bluebeam cloud & Incompatible tool sets
Note: I did some digging and used Co-pilot to help me write this, This reflects my use experience for the last 7 years of using Bluebeam review on project where we have hundreds of workers that were using the Bluebeam REVU. I have run massive QAQC jobs and Troubleshooting jobs Using Bluebeam review. The toolbox is one of…
-
Rectangle Select Not Working
The Object select tool is no longer working, to select multiple markups I have to hold shift and individually click each one. Also, when I select a markup, I have to press Esc to deselect it, rather than clicking away from it that would usually result in it being deselected. How can I revert both of these features back to…
-
AutoSize Text in Callout and Cloud+ Markups
Subject: Request for AutoSize Text in Callout and Cloud+ Markups Hi Team, Currently, Auto Size Text Box is only available for Text Box markups. In design review workflows, especially for engineering drawings, we frequently use Callout and Cloud+ markups. It would be very helpful if Auto Size Text Box functionality can be…
-
Bluebeam Sessions
Q1. Bluebeam Session- how can do the search option in Bluebeam sessions to find projects easily. Q2. Bluebeam Session – As now I have lots of session and like to have grouped in the session studio like Head folder and sub folder for project sessions per client or architect. Just to better the session organization.
