Can you create a button to mirror the PDF and it's not the same as rotating.
If I understand what you're looking for, to accomplish this today you could right-click on a page from the Thumbnails panel and choose Copy Page to Snapshot (Ctrl+Alt+C).
Next, create a new PDF with the same page size and then go to Edit > Paste in Place (Ctrl+Shift+V).
Then, right-click on the pasted snapshot > Alignment > Flip Horizontal (Ctrl+Alt+H).
Finally you'll want to flatten the snapshot so it is no longer an editable markup on top of the page. Right-click and select Flatten.
I realize this is several steps and not 1-click, and wouldn't be scalable for a lot of pages, but does this create the results you're looking for?
I'm curious about what scenario(s) you have to do this.
Also, how often do you have to do this, and for many documents/pages?
Hello!
I followed your steps in the discription above and it works just fine. I would like to take it a step further though.
The reason I want to do this is to overlap to another pdf (drawing) to se if there is any differences between them. This does'nt work when my new mirrored pdf is blank when i go to Document> Overlap pages. (se attatchements)
Is there any way to fix this?
Also, just to be sure. Is "Flatten" the command with the weight? I have a Swedish version of BB Revu so I have a bit of language issuses.
I'm not sure what is going on with your mirrored drawing as nothing shows up when you start to use the overlay function. However, have you just tried overlaying the original pages using the manual 3-point aligning i.e. without doing any sort of rotations?
Yes, the "Flatten" icon looks like a weight.
Something about 19-113 speglad doesn't allow the overlay to work. Without making any changes, the overlay doesn't recognize any of it's content so only the content from V-57-1-02-19-113 shows up.
I would have thought the instructions from @Jared Adler - Bluebeam CSM would have worked. Turns out that the Overlay tool ignores snapshots, even when flattened.
On the Bluebeam website, under "Resources" > "Need an older version of Revu?" there is only v20 and older. This needs new options, like v21.6. Currently the need for this is high, because v21.7 has a highly annoying "new feature" while drawing polylines, areas and contour and area measurement. Something goes visually wrong…
A mirror tool would be really helpful when sketching ideas.
Since the update, my area measurements have been messing up when I try to add a curve control point while measuring. I hold ctrl + click and drag and it almost always reverts back to a straight line when I release and adds a point where my cursor was holding the curve. Also, the lines/area disappear completely if I move…
I have been having issue with my Bluebeam/Revu that prevents me from carrying on with my work. Sometimes when a file is open and in the middle of working with the file, the following message pops up (see snippet below), which locks me out of continuing the work and forcing me to "End program" and restart Revu again. This…
I found this support article, but I don't see the options shown in the screenshot to send to Cloud. At the bottom of the tool set menu I only see Manage Tool Sets, there's no Send Tool Sets to Bluebeam Cloud.
In our work, we frequently need to compare floor plan drawings. Often, we have to compare older drawings from archives with very new and detailed ones. The scales of these drawings often differ — sometimes from 1:100 to 1:200, but more commonly with small variations of 1–5% at a detailed level. Our current workflow is as…
Long post for context: Yesterday I was trying to compare a revised architectural to realize that the floor plan has shifted in both the X and Y, so this morning I did a page snapshot. What I would like to know is, is there a way to snap to a point on the snapshot and move it to a point on the drawing?
Hi, I have just updated my bluebeam last weekend and when i am trying to measure, there is now a thick line which blocks the view of my clicking point. i have line weight disabled already. Its just when i am measuring via length, Polylength, area etc. it has slowed up my measuring process as i cant click on the points I am…
When extracting pages, I currently have to either: Select all pages first, then use Extract [Ctrl+Shift+X], or Go to Extract and change the page range dropdown from Selected to All Pages. Is there a way to skip these steps and have All Pages set as the default so I can extract the full document with a single click?